Basics
Tutorials
Projects
Interfaces
Integrations
Hardware
Firmware
tools
Documentation

Toolchain Guide

This document assumes that you have necessary tools installed according to the document Toolchain Setup.

All of the steps below assume work with BigClown Toolchain in Windows or with the Terminal application in macOS or Ubuntu.

Program BigClown Firmware Tool

The program BigClown Firmware Tool (bcf) simplifies the firmware workflow.

This tool allows to:

  • Manipulate with firmware packages:

    • Update package database (bcf update)

    • Listing from package database (bcf list)

    • Search in package database (bcf search)

    • Download package for offline use (bcf pull)

  • Upload firmware (bcf flash)

  • Create empty project for firmware development (bcf create)

We will show the individual operations in the following chapters.

BigClown projects offer pre-compiled firmware binary images in the section Releases of the given GitHub repository.

The bcf tool has a built-in help system. You can see the basic list of commands by using bcf help:

usage: bcf [-h] [-v] COMMAND ...
BigClown Firmware Tool
positional arguments:
COMMAND
update update list of available firmware
list list firmware
flash flash firmware
devices show devices
search search in firmware names and descriptions
pull pull firmware to cache
clean clean cache
create create new firmware
read download firmware to file
help show help
optional arguments:
-h, --help show this help message and exit
-v, --version show program's version number and exit

Detailed usage of a given command using e.g. bcf help flash:

usage: bcf flash
bcf flash <firmware>
bcf flash <file>
bcf flash <url>
optional arguments:
-h, --help show this help message and exit
--device {/dev/ttyUSB0}
device
--dfu use dfu mode

Device Firmware Upgrade (DFU) is a vendor- and device-independent mechanism for upgrading the firmware of USB devices

Firmware Package Listing

Use this command to update the list of available firmware packages:

bcf update

Always use this command before listing the available packages.

Use this command to list the available firmware packages:

bcf list

Example output:

...
bigclownlabs/bcf-gateway-usb-dongle:v1.10.0
bigclownlabs/bcf-radio-climate-monitor:v1.3.0
bigclownlabs/bcf-radio-co2-monitor:v1.4.0
bigclownlabs/bcf-radio-door-sensor:v0.2.0
bigclownlabs/bcf-radio-flood-detector:v1.3.0
bigclownlabs/bcf-radio-lcd-thermostat:v1.4.0
bigclownlabs/bcf-radio-motion-detector:v1.3.0
bigclownlabs/bcf-radio-power-controller-rgb150:v1.4.1
bigclownlabs/bcf-radio-power-controller-rgbw144:v1.4.1
bigclownlabs/bcf-radio-power-controller-rgbw36:v1.4.1
bigclownlabs/bcf-radio-power-controller-rgbw72:v1.4.1
bigclownlabs/bcf-radio-push-button:v1.3.0
bigclownlabs/bcf-radio-voc-sensor:v1.0.0
...

Use this command to list all the versions of the available firmware packages:

bcf list --all

Use this command to search in the available packages (in their title and description):

bcf search <searched term>

Firmware Upload

There are two bootloaders in MCU ROM:

  • DFU - in case of USB device in MCU is used (e.g. for Core Module R1.3)

  • UART - in case of USB-UART chip device is used (e.g. for Radio Dongle or Core Module R2.x)

In case you need to upload the firmware into the Core Module R1, you must first put it in the DFU mode. Moreover, the flash command must be in the bcf flash --device dfu format.

Flashing Core Module R1 & R2 For differences of flashing older Core Module 1 and newer Core Module 2 please read Core Module R1 and R2 comparison in the Hardware section

Firmware upload can be done using the bcf flash command. The firmware can be obtained from 3 different sources:

Step 1: Source firmware package, for instance

bcf flash bigclownlabs/bcf-radio-push-button:latest

Step 2: Source local disk file, for instance

bcf flash firmware.bin

Step 3: Source file from the specified URL, for instance

bcf flash https://github.com/bigclownlabs/bcf-radio-push-button/releases/download/v1.1.0/bcf-radio-push-button-v1.1.0.bin

You can list the USB UART devices connected to your host using this command:

bcf devices

...and then use the device from the list altogether with the --device parameter, e.g.:

bcf flash --device /dev/ttyUSB0 bigclownlabs/bcf-gateway-usb-dongle:latest

this way the bcf will not ask you which serial port to use every time.

Firmware Package Cache

If the firmware does not exist in the local cache, it is download first with the first bcf flash command.

Also, if you need to download the firmware package and work with it later offline, you can download it using the bcf pull command, for instance:

bcf pull bigclownlabs/bcf-gateway-usb-dongle:latest

If you want to clean the cache of the firmware package list and all the downloaded packages, use this command:

bcf clean

Create Blank Firmware Project

Step 1: Go to the directory where you want to create a firmware directory

Step 2: Go to the directory where you want to create a firmware directory

bcf create <firmware-name>

Step 3: The bcf program cloned the basic firmware skeleton, which is ready to build immediately (see description below)

The starting point for developing your own firmware is the file app/application.c.

Build Firmware

Firmware build is done using the traditional traditional build system GNU Make, which follows the recipe given in the file Makefile (found in the firmware root directory).

There are 2 target configurations to build the firmware:

  • debug

    This configuration is implicit and is suitable for firmware development. The built-in firmware is ready for debugging.

  • release

    This configuration is suitable for final deployment. It has build some optimizations turned on and is not suitable for firmware debugging due to these optimizations. The resulting program in this configuration can run faster and show lower power consumption than the one in debug configuration.

You can build the firmware by following these steps:

Step 1: Go to the firmware directory you want to build

Step 2: Run the build command

make

Build process can be accelerated by specifying the number of parallel compiler processes through the parameter -j<number>. The number should match the number of cores in your processor. Example: make -j4

Step 3: Upon successful completion of the build process, you will receive a similar listing at the end

Linking object files...
Size of sections:
text data bss dec hex filename
74332 2776 7328 84436 149d4 out/debug/firmware.elf
Creating out/debug/firmware.bin from out/debug/firmware.elf...

Step 4: The program called linker created two important files

  • out/debug/firmware.elf

    This is the file in ELF format containing symbols necessary for a debugger.

  • out/debug/firmware.bin

    This is the binary image necessary for programming (the ELF file also contains this binary image).

Step 5: In order to build the firmware in release configuration, use this command

make release

This command generates the file out/release/firmware.bin.

Switching Core Module into DFU Mode

To program the Core Module, we must first enter the DFU mode.

We can do this by following this procedure:

Step 1: Check that the USB cable is plugged into the Core Module and your computer

Step 2: Press and hold the BOOT button on the Core Module

The BOOT button is on the right and is marked with a letter B.

Step 3: Press and release the RESET button on the Core Module. At this point, you still have to hold the BOOT button

The RESET button is on the left and is marked with a letter R.

Step 4: Release the BOOT button

Now the Core Module is connected to your computer as a DFU USB device and is ready for programming.

Windows DFU Driver Troubleshooting

Incorrect DFU Driver

In case you get Cannot open DFU device 0483:df11 while running the bcf flash --device dfu command, you have the incorrect DFU drivers installed.

Step 1: Execute zadig from Toolchain or Playground shell (from cmd.exe BigClown window)

Keep the Core Module connected with the DFU mode activated.

Step 2: Allow admin rigths in the User Acess Control pop-up

Step 3: Select Options -> List All Devices

Step 4: Choose STM32 BOOTLOADER

Step 5: Choose WinUSB

Step 6: Click on Replace Driver

You will get The driver was installed successfully notification.

Step 7: Exit Zadig and get back to firmware flashing. The DFU driver repair procedure is finished

Step 8: You can check DFU readiness using the dfu-util -l command from BigClown Toolchain Prompt

No DFU Device Found

There is not Cannot open DFU device 0483:df11 between:

A valid DFU suffix will be required in a future dfu-util release!!!
No DFU capable USB device available

There can be various reasons:

Step 1: DFU mode is not activated on the Core Module

Follow the instructions in the chapter Switching Core Module into DFU Mode.

Step 2: Defective USB cable, USB hub, USB port or Core Module

  • Try different hardware.

  • Try connection without a USB hub.

  • Make sure the USB cable used has data wires (some USB cables are for powering only).

Step 3: Connection mismatch - the Core Module is connected to different host than where bcf is executed

  • Connect the Core Module to the right host.

Related Documents